Here you will find presentations given at COMSOL Conferences around the globe. The presentations explore the innovative research and products designed by your peers using COMSOL Multiphysics. Research topics span a wide array of industries and application areas, including the electrical, mechanical, fluid, and chemical disciplines. Use the Quick Search to find presentations pertaining to your application area.
COMSOL-News-Magazine-2017
COMSOL-News-Magazine-2017-Special-edition-acoustics
COMSOL-News-Magazine-2016

Simulator for Automotive Evaporative Emissions Restraint Systems

S. Schlüter [1], E. Schieferstein [1], T. Hennig [1], K. Meller [1],
[1] Fraunhofer UMSICHT, Oberhausen, Germany

Fuel vapor restraint systems are used in vehicles to avoid discharge of volatile hydrocarbons from fuel tanks. The topic of this paper is the proper operation of fuel vapor restraint systems depending on the composition of bioethanol-fuel-blends. Experimental data serve as input to a model built with COMSOL Multiphysics® to simulate the performance of fuel vapor restraint systems depending on ...

CVD Graphene Growth Mechanism on Nickel Thin Films - new

K. Al-Shurman[1], H. Naseem[2]
[1]The Institute for Nanoscience & Engineering, University of Arkansas, Fayetteville, AR, USA
[2]Department of Electrical Engineering, University of Arkansas, Fayetteville, AR, USA

Chemical vapor deposition is considered a promising method for synthesis of graphene films on different types of substrate utilizing transition metals such as Ni. However, synthesizing a single-layer graphene and controlling the quality of the graphene CVD film on Ni are very challenging due to the multiplicity of the CVD growth conditions. COMSOL Multiphysics® software is used to investigate ...

Fluid Motion Between Rotating Concentric Cylinders Using COMSOL Multiphysics® Software

P. L. Mills [1], K. Barman [1], S. Mothupally [1], A. Sonejee [1],
[1] Texas A&M University - Kingsville, Kingsville, TX, USA

Introduction Fluid flow patterns in research or process-scale equipment where a fluid is contained between concentric rotating cylinders in the absence of bulk axial flow has received notable attention in the field of fluid mechanics. Annular flows occur in many practical applications, such as in the production of oil and gas, fluid viscometers, centrifugally-driven separation processes, ...

Modeling of Residual Stresses in a Butt-welded Joint with Experimental Validation

V. Srivastava [1],
[1] Naval Materials Research Laboratory (NMRL), Defence Research and Development Organization (DRDO), Ambernath, Thane, Maharashtra, India

2D-modeling of arc welding in butt-joint configuration was performed in this study considering thermal-structural interactions. Thermal behavior was modeled in COMSOL Multiphysics® using the Heat Transfer Module with weld heat input as a Gaussian pulse whereas structural behavior using Structural Mechanics Module. Thermal-elastic-plastic behavior model based on Von Mises yield criteria and ...

A Wall-Cooled Fixed-Bed Reactor Model for Gas-Phase Fischer-Tropsch Synthesis

A. Nanduri [1], P. L. Mills [1],
[1] Department of Chemical and Natural Gas Engineering, Texas A&M University - Kingsville, Kingsville, TX, USA

In the early 1920’s, Gas-To-Liquids (GTL) and Coal-To-Liquids (CTL) technologies were developed to account for the depleting crude oil resources [1]. During this period, Franz Fischer and Hans Tropsch developed a process to convert synthesis gas (syn gas), derived from coal gasification, to a wide range of high value-added products. This process later came to be known as Fischer-Tropsch (F-T) ...

Ammonia Removal From Water by a Liquid-Liquid Membrane Contactor Under a Closed Loop Regime

E. Licon[1], S. Casas[1], A. Alcaraz[1], J.L. Cortina[1], C. Valderrama[1]
[1]Universitat Politécnica de Catalunya, Barcelona, Spain

Ammonia separation from water by membrane contactor was simulated on transient state and compared with experimental data. Aqueous low concentrated solution of ammonium with high pH has been pumped inside the hydrophobic hollow fibers, acid solution in the outside part. The system is in closed loop configuration. In order to simulate the separation process, equations were developed considering ...

Development of a User Interface for Design of SO2 Oxidation Fixed-Bed Reactors

A. Nagaraj [1], P. L. Mills [1],
[1] Texas A&M University - Kingsville, Kingsville, TX, USA

H2SO4 is a very important chemical commodity, and indeed, a nation’s H2SO4 production has been a reasonably good indicator of its industrial strength for the last century or so1,2. Nearly 350 MM tons of H2SO4 was produced in 20143.The demand for H2SO4 in United States exceeds the supply and hence to increase production, recycling and innovative clean technologies must be explored. From ...

The Effects of the Contact Angle on the Dynamics of Water Droplet Impingement

J. Hu [1], X. Huang [2], X. Xiong [1], K. T. Wan [2],
[1] University of Bridgeport, Bridgeport, CT, USA
[2] Northeastern University, Boston, MA, USA

INTRODUCTION The dynamic behavior of droplet impingement on a solid surface is important to many engineering applications, such as rain drops on automobile windshields, inkjet deposition and metal deposition in manufacturing processes, spray cooling of electronics, and spray coating for various applications. The droplet can spread, splash, and rebound after hitting a solid surface. Contact ...

Understanding the Transition Flow Region through Modeling in COMSOL Multiphysics® Software

J. Sturnfield [1],
[1] Dow Chemical, Freeport, TX, USA

The pore sizes of many membranes being studied for separating the components in gas mixtures are on the scale of nanometers. Depending on the specific gases and pressures being used, this scale will put the flows in the Transition between Slip Flow and Knudsen regime. The differential flow of the gas components gives the relative diffusion of the gases through the membrane. There are a number of ...

Numerical Model for Predicting Heat and Mass Transfer Phenomena during Cake Baking

P. Le Bideau [1], R. Cutté [1], P. Glouannec [1], J. F. Le Page [2]
[1] Univ. Bretagne Sud, FRE CNRS 3744, IRDL, F-56100 Lorient, France
[2] DPP, ADRIA Développement, Quimper, France

A transient two-dimensional axisymmetric model is implemented in COMSOL Multiphysics® software to simulate temperatures, moisture contents distributions and cake swelling during the baking of cake contained in mold. The medium is assumed to be a deformable porous medium containing three phases: solid (dough), liquid (water) and gas. Gas phase includes two species, water and carbon dioxide. The ...

First
Previous
1–10 of 395