Here you will find presentations given at COMSOL Conferences around the globe. The presentations explore the innovative research and products designed by your peers using COMSOL Multiphysics. Research topics span a wide array of industries and application areas, including the electrical, mechanical, fluid, and chemical disciplines. Use the Quick Search to find presentations pertaining to your application area.
COMSOL-News-Magazine-2017
COMSOL-News-Magazine-2017-Special-edition-acoustics
COMSOL-News-Magazine-2016

COMSOL Multiphysics® Software: Simplifying Workflow and Promoting Innovations in Nuclear Engineering at ORNL

P. K. Jain [1], J. D. Freels [1],
[1] Oak Ridge National Laboratory, Oak Ridge, TN, USA

At Oak Ridge National Laboratory (ORNL), COMSOL Multiphysics® software has become a preferred software for certain multiphysics applications in nuclear engineering. This presentation will highlight some of the ongoing activities in the following areas: (1) Highly enriched uranium (HEU) to low enriched uranium (LEU) conversion of the High Flux Isotope Reactor (HFIR), (2) New and improved safety ...

Investigation of Performance of SOFC in Hydrocarbon Fuel

S. T. Aruna [1], S. Senthil[1], S. Chauhan [1], B. Shriprakash [1],
[1] CSIR-National Aerospace Laboratories, Bangalore, Karnataka, India.

SOFC is a high temperature electrochemical device known for its fuel flexibility. Apart from using pure hydrogen, it can utilize CO (carbon monoxide), CH4 (methane) or any other higher hydrocarbon. Since methane is highly researched hydrocarbon fuel, it was chosen to start with. The most prominent problem faced while using hydrocarbon fuel in SOFC is the formation and deposition of carbon on the ...

单匝线圈脉冲放电研究

郝帅翔 [1], 蒋帆 [1],
[1] 华中科技大学,武汉,中国

利用高压电容器对单匝线圈放电是产生脉冲强磁场的技术之一,其电路模型简单,可以等效成RLC串联电路,但过程复杂,涉及电磁学、力学、热学、等离子体科学等众多学科。本文分析了其具体过程,并利用 COMSOL Multiphysics® 仿真平台进行了模拟,建立了二维和三维单匝线圈模型,重点研究了线圈的动态特性对磁场分布的影响,并对比了其结果和模型准确性;然后,讨论了线圈的尺寸和所产生磁场的关系;最后通过实验验证了仿真模型的准确性,为今后的相关科学研究奠定了基础。

Microfluidic Separation System for Magnetic Beads

F. Wittbrach, A. Weddemann, A. Auge, and A. Hütten
Department of Physics, Bielefeld University, Germany

It is possible to control the motion of magnetic beads using a combination of hydrodynamic and electromagnetic forces. In this work, we investigate the possibility to manipulate the motion of beads with different magnetic moments in a special microfluidic structure so as to separate them. We also experimentally prove that this structure is a suitable device to separate beads and show that the ...

Shape, Convection and Convergence

R. Pryor
Pryor Knowledge Systems, Inc., Bloomfield Hills, MI, USA

COMSOL Multiphysics software, when properly configured, can readily solve modeling problems in the laminar flow regime using the standard Navier-Stokes equations or in the fully turbulent flow regime using the kappa-epsilon model. Failure to solve a particular model is typically manifested by instability in the calculation and a failure of the model to converge. This paper presents a new ...

Using Perturbation Force Analysis for the Design of a Levitronc: an Application of Magnetic Levitation

Z. De Grève[1,2], C.Versèle[1], and J.Lobry[1]
[1]Faculty of Engineering, Mons, Belgium
[2]Belgian Fund for Research, F.R.S./FNRS, ResearchFellow, Belgium

The Levitron offers an interesting demonstration of natural magnetic levitation using permanent magnets. It is composed by a small magnetized top and a circular magnetized base with a hole on its center. The top is placed in an area where magnetic field configuration and gyroscopic torques allow the existence of a locus of stable equilibrium. In this paper, we intend to dimension and realize a ...

Simulation of Topology Optimized Electrothermal Microgrippers

O. Sardan[1], D. Petersen[1], O. Sigmund[2], and P. Boggild[1]
[1]DTU Nanotech, Denmark
[2]DTU Mechanical Engineering, Denmark

In this work, electrothermal microgrippers designed using topology optimization are modeled. The microgrippers are composed of two 5 μm-thick polysilicon actuators facing each other. The gap between the actuators are 2 μm in the initial state and the microgrippers are able to both fully close and further open this gap. The operation principle of the actuators is quite similar to that of a ...

Development of an Interlinked Curriculum Component Module for Microchemical Process Systems Components Using COMSOL Multiphysics

A. Mokal, and P. Mills

Department of Chemical and Natural Gas Engineering, Texas A&M University, Kingsville, TX, USA

COMSOL Multiphysics provides a powerful numerical platform where various models for microchemical process technology components can be readily created for both education and research. This modeling tool allows chemical engineering students to focus on understanding the effects of various microchemical system component design and operational parameters versus coding and debugging of the numerical ...

COMSOL Multiphysics Modeling of Rotational Resonant MEMS Sensors with Electrothermal Drive

S. Nelson[1], and M. Guvench[1]
[1]University of Southern Maine, Gorham, Maine, USA

COMSOL Multiphysics is employed to model, simulate and predict the performance of a high Q, in-plane rotational resonating MEMS sensor. The resonating sensor disk is driven by thermal expansion and contraction of the support tethers due to AC joule heating. The resonant frequency is sensed by stationary contacts. For cost reduction, the relatively simple, low cost SOIMUMPS fabrication process is ...

Image-Based Simulation of Electrical Impedance Techniques Applied on the Human Thorax for Cardio-Pulmonary Applications

F.K. Hermans[1], R.M. Heethaar[1], R.T. Cotton[2], and A. Harkara[2]


[1]VU University Medical Center, Amsterdam, The Netherlands
[2]Simpleware Ltd., Exeter, United Kingdom

For medical diagnostic purposes there is an increasing need for non- (or minimal) invasive techniques to measure all kinds of parameters that can provide insight in the functioning of cells, organs or organ systems. Currently, Impedance Cardiography (ICG) is used for measurements of the heart and Electric Impedance Tomography (EIT) is used for investigating lung tissue condition. This paper ...