Here you will find presentations given at COMSOL Conferences around the globe. The presentations explore the innovative research and products designed by your peers using COMSOL Multiphysics. Research topics span a wide array of industries and application areas, including the electrical, mechanical, fluid, and chemical disciplines. Use the Quick Search to find presentations pertaining to your application area.
COMSOL-News-Magazine-2017
COMSOL-News-Magazine-2017-Special-edition-acoustics
COMSOL-News-Magazine-2016

Flare System Pressure Drop Calculations Using COMSOL

K. Alhazza[1], B. Albusairi[1], H. Kamal[1], H.M.S. Lababiedi[1], A.A. Abbas[2]
[1]Kuwait University, Kuwait City, Kuwait
[2]Petrochemical Industries Company, Kuwait City, Kuwait

COMSOL Multiphysics has been used to validate and check the design of a header transporting ammonia gases released from pressure safety valves (PSVs) to the tip of the flare. The header is part of a dedicated flaring system to contain emissions from ammonia storage tanks. The two main challenges are the low relief pressure and high capacity of the system. Another difficulty is the high relief ...

A MEMS Condenser Microphone for Consumer Applications

S. Kesari[1], A. Pandit[1], K. Mishra[1], Kaushal B. K.[1]
[1]Electronics and Communication Engineering, Nitte Meenakshi Institute of Technology, Bangalore, India

The MEMS microphone is also called microphone chip or silicon microphone.The pressure sensitive diaphragm is etched directly into a silicon chip by MEMS techniques and is usually accompanied with integrated preamplifier. Most MEMS microphones are variants of the condenser microphone design. The device consists of a polysilicon diaphragm suspended over a single crystal silicon backplate ...

Optimizing Fuel Cell Design with COMSOL Multiphysics

Chin-Hsien Cheng[1]
[1]Renewable Energy RD Center, Chung-Hsin Electric & Machinery, Taiwan

Proton exchange membrane fuel cells (PEMFCs) were investigated using COMSOL Multiphysics with the AC/DC Module and Chemical Engineering Module. Simulation may be used to increase the performance while decreasing the cost of the catalyst later (CL). Experimental validation of single and multi-layer CL was performed for varied PBI electrolyte content. The validated model was used to investigate ...

Investigation of Blade Profiles of Vertical Axis Wind Turbine by Numerical Simulation

S. Yoshioka[1]
[1]Ritsumeikan University, Kusatsu City, Shiga, Japan

There are two types of vertical axis wind turbine, drag-type and lift-type. Drag type wind turbine can rotate in low speed wind condition, although its rotation speed is low. Lift type wind turbine can rotate at higher speed, although it works only in high speed wind condition. This study investigates new blade profile that realize rotation in low wind speed condition and higher rotation speed ...

Numerical Modeling of a Microtubular Solid Oxide Fuel Cell Using COMSOL Multiphysics®

P. Pianko-Oprych[1], E. Kasilova[1], Z. Jaworski[1]
[1]West Pomeranian University of Technology, Faculty of Chemical Technology and Engineering, Szczecin, Poland

Micro-tubular Solid Oxide Fuel Cells (mSOFC) are attracting more and more interest as new generation of energy conversion devices. Although commercial applications still suffer from high costs, there is a need for further improvement of the cell performance, durability and start-up. To resolve those challenges, knowledge of the distributions of species concentration, temperature and current ...

Electrochemical Pickling of Steel for Industrial Applications: Modeling

M. Freda[1], A. Giannetti[1], L. Lattanzi[1], S. Luperi[1]
[1]Centro Sviluppo Materiali, Rome, Italy

The electrochemical pickling of steel has two main purposes: 1) To remove thermal oxide; 2) To dissolve chromium-depleted layer, to reinstate the corrosion-resistant properties of the stainless steel; A reliable, flexible and robust 3D model has been made for simulating the steel electrochemical pickling. This process is modeled as a multiphysics system for the current control. The model ...

Modeling Magnetic Induction from Transient Events Impinging upon a Conducting Moon

H. Fuqua[1], G. Delory[1], I. de Pater[2], R. Grimm[3]
[1]University of California - Berkeley, Space Sciences Lab, Berkeley, CA, USA
[2]University of California - Berkeley, Berkeley, CA, USA
[3]Southwest Research Institute, Boulder, CO, USA

Electromagnetic sounding measurements utilize magnetic induction to constrain the interior geophysical properties of planetary bodies. Under some conditions, the Earth’s moon can be approximated by the response of a conducting sphere in a vacuum. Transient magnetic fields originating from the sun can interact directly with the moon, producing eddy currents that generate an induced magnetic ...

Chromatographic Separation of Tröger’s Base in a Batch Column

A. Fayolas [1], M.G. Sanku[1], M. Pascoa[1], M. Xynou[1]
[1]KTH Royal Institute of Technology, Stockholm, Sweden

The objective of the study is to investigate the chiral separation of Tröger’s base enantiomers using batch chromatography. Because of its resolution, chromatography is often the preferred method for chiral separations. The separation of Tröger’s base is resolved by using the COMSOL Multiphysics® software. It is modeled by one dimension geometry, having the length of the column set and computed ...

Integrated Solar Thermal Collector with Heat Storage

A.R. Sánchez-Guitard[1], E. Ruiz-Reina[1]
[1]University of Málaga, Málaga, Spain

In this work, we study the design of a new integrated system for Solar Water Heating that combines the solar thermal energy collection (primary circuit) with the heat storage (secondary circuit) into the same device. We have performed different finite element method simulations using COMSOL Multiphysics®, for solving the equations of heat transfer (conduction and convection) and those of fluid ...

Calculation in Coupling Coefficient of 1.3μm Quantum Dots Distributed Feed Back Laser with Half Etched Mesa Structure

Keishiro GOSHIMA et al.[1]

[1]Aichi Institute of Technology, Toyota, Aichi, Japan

Quantum Dots (QDs) laser is expected to have a low threshold current density and high thermal stability. We propose the QDs laser with the half-etched mesa distributed feedback (HEM DFB) structure. We accurately calculated the coupling coefficient in a HEM waveguide using the finite element method (FEM).