Comparison Between Phase Field and ALE Methods to Model the Keyhole Digging During Spot Laser Welding
V. Bruyere, C. Touvrey, P. Namy
CEA-DAM, Is-sur-Tille, France
SIMTEC, Grenoble, France
Nowadays, spot laser welding is a full-fledged part of industrial manufacturing and is routinely used due to its advantages. It generates very located temperature gradients, and therefore, induces small distortions in the pieces. The COMSOL Multiphysics® software is used to model the interaction stage of an isolated impact made with a Nd:YAG pulsed laser. The free surface evolution has been ...
M. Curatolo , L. Teresi ,
 Department of Engineering, Università Roma Tre, Roma, Italy
 Department of Mathematics and Physics, Università Roma Tre, Roma, Italy
Our goal is to reproduce the key features of carangiform swimming by running 2D simulations which fully exploit the Fluid-Structure Interaction interface of COMSOL Multiphysics software. Fish swimming is an important area of research, with relevant developments on biomechanics, robotics and mathematical modeling. Usually, in fish swimming simulations, the motion of the fish is assigned, and much ...
P. L. Mills , K. Barman , S. Mothupally , A. Sonejee ,
 Texas A&M University - Kingsville, Kingsville, TX, USA
Introduction Fluid flow patterns in research or process-scale equipment where a fluid is contained between concentric rotating cylinders in the absence of bulk axial flow has received notable attention in the field of fluid mechanics. Annular flows occur in many practical applications, such as in the production of oil and gas, fluid viscometers, centrifugally-driven separation processes, ...
L. R. de Souza Jr., L. Lorenz
Universidade Federal do Paraná, Curitiba, Paraná, Brazil
In the core of Chemical Engineering is the reactor design that includes most of all scientific disciplines. The reactors, in general, are treated ideally. Unfortunately, it is observed in the real world a very different behavior from that expected. Thus, to characterize nonideal reactors is used, among others, residence time distribution function E(t). The aim of this present work is to ...
Ravindra Mane, Sandeep soni
Department of Mechanical Engineering, Sardar Vallabhbhai National Institute of Technology, Surat, Gujarat, India
This paper presents the 3D model of hydrodynamic plain journal bearing using COMSOL Multiphysics®. Using 3D Model, pressure distribution in plain journal bearing is obtained by steady state analysis of plain journal bearing. Generalized Reynolds equation is used for analyzing hydrodynamic journal bearing by COMSOL Multiphysics® as well as by analytical method by applying Sommerfeld boundary ...
S. Gorelick, M. Leivo, U. Kantojärvi
VTT Technical Research Centre of Finland, Espoo, Finland
Excessive air damping can be detrimental to the performance of oscillating MEMS components. Complex systems, such as structures in pre-etched cavities or angular comb-drive scanning mirrors, typically require simulations to reliably evaluate the air damping. The simulated and experimental performance of the following systems was evaluated and compared: two types of out-of-plane cantilevers, in ...
J. Sturnfield ,
 Dow Chemical, Freeport, TX, USA
The pore sizes of many membranes being studied for separating the components in gas mixtures are on the scale of nanometers. Depending on the specific gases and pressures being used, this scale will put the flows in the Transition between Slip Flow and Knudsen regime. The differential flow of the gas components gives the relative diffusion of the gases through the membrane. There are a number of ...
A. Métais , S. Matteï , I. Tomashchuk , S. Gaied 
 ArcelorMittal, Montataire, France
 Laboratoire Interdisciplinaire Carnot de Bourgogne, Université Bourgogne Franche Comté, France
Laser Welded Blank solutions enable to reduce vehicles weight and to optimize their crash performances by means of simultaneous tuning of different grades and thicknesses. The present work aims to characterize numerically and experimentally materials mixing during laser welding. For better understanding of materials mixing based on convection-diffusion process in case of full penetrated laser ...
M. K. Gobbert, X. Huang, S. Khuvis, S. Askarian, B. E. Peercy
University of Maryland - Baltimore County, Baltimore, MD, USA
This paper presents information on techniques needed in COMSOL Multiphysics® to enable computational studies of coupled systems of PDEs for time-dependent non-linear problems. Furthermore, we demonstrate how to use data files as input for initial conditions. To illustrate the techniques, we consider a system of two time-dependent non-linear PDEs from mathematical biology that couples an ...
M. Diaz-Viera, D. Lopez-Falcon, A. Moctezuma-Berthier, and A. Ortiz-Tapia
Instituto Mexicano del Petroleo, México D.F., Mexico
The aim of the present work is to implement in COMSOL Multiphysics a multiphase fluid flow model in porous media, also known in the oil reservoir engineering literature as a black oil model, using a standard finite element approach. In particular, we are interested to apply this model coupled with a multiphase, multicomponent transport model to study Enhanced Oil Recovery processes at laboratory ...