A. R. Kalaiarasi, and S. H. Thilagar
Electrothermal actuators are capable of providing larger displacements compared to electrostatic actuators. Four designs for ETC actuators with the same material properties and same dimensions are studied.
D. Maji, C. P. Ravikumar, and S. Das
School of Medical Science and Technology, Indian Institute of Technology, Kharagpur, West Bengal, India
Texas Instruments (India) Pvt. Ltd., Bangalore, India
Arterial disease, especially Coronary Artery Disease (CAD) is one of the leading causes of premature morbidity and mortality. During the flow, blood interacts with vessel wall mechanically and chemically which modulates the plaque formation in blood vessel leading to coronary artery diseases. Here we propose to simulate a MEMS based flexible flow sensor based on anemometer principle designed to ...
G. Vijila, S. Vijayakumar, M. Alagappan, and A. Gupta
PSG College of Technology
Tamil Nadu, India
This paper projects a novel 3D capacitive accelerometer design to identify a severe accident and initiate airbag deployment systems. It will detect the rapid negative acceleration of the vehicle to avoid the severity of the collision. Such a device demands excellent performance in terms of sensitivity, noise immunity, linearity, bias and scale factor stability over time and environmental ...
Effect of Bed Diffusion and Operating Parameters on Char Combustion in the Context of Underground Coal Gasification
S. Mahajani, and G. Samdani
Indian Institute of Technology Bombay
Char combustion is one of the most important reactions in the process of Underground Coal Gasification (UCG). Experiments are performed in a boat reactor under near isothermal condition to demonstrate effects of heat and mass transfer and bed diffusion through ash layer. To obtain a complete overview of boat experiments and to further get insights, CFD analysis of boat reactor is performed using ...
Evaluation of Tensile Modulus of Carbon Nanotube Bundle Based Composite with Interface Using Finite Element Method
M. S. Islam, F. O. Riktan, S. C. Chowdhury, M. M. R. Chowdhury, and S. Ahmed
Bangladesh University of Engineering & Technology (BUET)
Carbon Nanotubes (CNTs) have remarkable mechanical, thermal and electrical properties. The properties of CNTs depend on atomic arrangement (how the sheets of graphite are rolled), the diameter and length of the tubes and morphology of nanostructure. In this paper effective elastic properties of CNT based polymer composites are evaluated using a square Representative Volume Element (RVE) in ...
C. Rajni, and A. Marwaha
 Shaheed Bhagat Singh College of Engineering And Technology, Ferozepur, Punjab, India
 Sant Longowal Institute of Engineering And Technology, Sangrur, Punjab, India
‘Metamaterial’ is one of the most recent topic in several areas of science and technology due to its vast potential in various applications. These are artificially fabricated materials which exhibit negative permittivity and/or negative permeability. The unusual electromagnetic properties of metamaterial has opened more opportunities for better antenna design to surmount the limitations of ...
Numerical Study on Mechanical Properties of Stents with Different Materials during Stent Deployment with Balloon Expansion.
P. Ghosh, K. DasGupta, D. Nag, and A. Chanda
School of Bio Science & Engineering, Jadavpur University, Kolkata, West Bengal, India
Mechanical Engineering Department, Jadavpur University, Kolkata, West Bengal, India
The main reason for stent implantation is to provide mechanical support to the arterial wall. So it is important to consider the different mechanical properties of different stent materials while studying the stent implant’s efficacy. The present study gives a comparative overview of mechanical aspects of different stent materials which are most commonly used in angioplasty. Deformation ...
R. C. Thiagarajan
ATOA Scientific Technologies Private Limited, Bangalore, India
Conductive Composites such as carbon fiber reinforced composites are increasingly used in safety critical aerospace applications. The catastrophic macro structural failure of composite structures initiates from a micro level failure event such as fiber breaks. The ability to detect damage early on can improve the safety level and reliability of composite structures. A multilevel self-sensing ...
D. Das, S. Sohail, S. Das, and K. Biswas
Electrical Engineering Department, IIT Kharagpur, India
School of Medical Science and Technology, IIT Kharagpur, India
Electrowetting on Dielectrics (EWOD)systems is widely practiced digital microfluidic technique, used in Lab-on-a-Chip (LoC) system for biomedical application. In EWOD, with applied potential, the droplet minimizes its surface energy by transiting towards the actuated electrode. The problems with EWOD device for biological sample are that it will damage the cells if applied voltage across it ...
S. Gawade, P. P. Date, and S. B. Sharma
Production Engineering. Dept. SGGS IE&T, Nanded, India
Mechanical Engineering. Dept, IIT, Bombay, India
Electromagnetic forming (EMF) is a typical high speed forming process using the energy density of a pulsed magnetic field to form workpieces made of metals with high electrical conductivity like e.g. aluminium. This forming process can be very advantageous as compared to conventional forming process. EMF process is simulated by a commercial finite element analysis (FEA) solver, COMSOL ...