C. Gavrila and I. Lancranjan
Technical University of Civil Engineering Bucharest, Bucharest, Romania
Advanced Study Centre, National Institute for Aerospace Research “Elie Carafoli”, Bucharest, Romania
Fiber optic sensors can measure a large range of physical, chemical and environmental variables such as temperature, pressure, shape, position, chemical concentration, moisture, etc. Fiber optic sensors provide measurements in applications where the conventional electrical based sensors cannot be used, due to measurement requirements such as extreme temperature, small size, high sensor count, or ...
P.A. Wallace, M. Alsharif, D.M. Hepburn, and C. Zhou
Department of Energy Systems Engineering, Glasgow Caledonian University, Glasgow, United Kingdom
Two simulations of the performance of a Paper Insulated Lead Covered (PILC) Medium Voltage (MV) underground cable are presented. The first presents the thermal response of a cable, over seven days, to a realistic load with a diurnal variation. The second concentrates on the variation of the electric field stress within the cable over a single AC cycle. The effects of a void defect within the ...
C. Caruso, P. Lonetti, and A. Manna
Department of Structural Engineering, University of Calabria, Arcavacata di Rende, CS, Italy
A generalized model to predict dynamic crack propagation in fiber composite structures is proposed. The proposed approach is based on a generalized formulation based on the Fracture Mechanics approach and Moving mesh methodology. Consistently to the Fracture Mechanics, the crack propagation depends from the energy release rate and its mode components, which are calculated by means of the ...
N. Fillot, T. Doki-Thonon, and W. Habchi
CNRS, INSA, Université de Lyon, Lyon, France
Department of Industrial and Mechanical Engineering, Lebanese American University, Byblos, Lebanon
A ball is in contact with a plane, and a lubricant separates the two surfaces to decrease friction during their relative motion. To avoid wear, the lubricant film thickness should be higher than the surface roughness. The goal of this paper is to show how it is possible to solve efficiently the problem of elastohydrodynamics lubrication with COMSOL Multiphysics®, using a PDE (Partial ...
Renewable Energies and Environmental Technologies Research Unit, Fondazione Bruno Kessler, Povo, TN, Italy
Stationary flow configurations in curved pipes constitute an important subject from both the theoretical and the practical point of view. A typical application concerns the calculation of secondary flow effects on the thermal efficiency of heat exchangers. Motivated by a similar problem, this paper investigates the flow patterns in a helical duct of non trivial cross section. The considered ...
L. Armellin, F. Gatelli, and G. Tanghetti
R&D Department, Metelli S.p.A., Cologne, BS, Italy
Ball joints are widely used in many applications. This paper describes the contact and kinematic analysis of an Rzeppa type constant-velocity joint (CV-joint). Starting from a conveniently simplified 3D model, at fixed joint angle of 45°, a CV-joint made of all “generic steel” components has been studied. Considering only a “perfect” geometry (i.e. not affected by ...
V.M. Rodriguez-Zermeno, M.P. Sørensen, N.F. Pedersen, N. Mijatovic, and A.B. Abrahamsen
DTU Mathematics, Lyngby, Denmark
DTU Electrical Engineering, Lyngby, Denmark
Materials Research Division, Risø, DTU, Roskilde, Denmark
This work presents a method to calculate AC losses in thin conductors such as the commercially available second generation superconducting wires through a multiscale meshing technique. The main idea is to use large aspect ratio elements to accurately simulate thin material layers. For a single thin superconductor, several standard test cases are simulated including transport current, externally ...
Danish Technological Institute, Aarhus C, Denmark
The use of the finite element method for understanding and analyzing the freezing and drying processes of food products is in focus in this paper. The objective of this study is to develop a model that can predict temperature distribution and weight loss of food products during the freezing and drying processes. The problem was solved by utilizing heat, mass transfer and moving mesh model. In ...
Georg-August University, Göttingen, Germany
Viscous fingering is a topic of interest since the beginning of computational fluid dynamics. Here we focus on the classical constellation of miscible displacement, as it has been investigated in Hele-Shaw cells. A temperature or salinity front is entering with a fluid that has a different viscosity. The pure 1D flow is destabilized by the Saffman-Taylor instability. Using COMSOL Multiphysics® ...
N. Delmonte, M. Bernardoni, P. Cova, and R. Menozzi
Dipartimento di Ingegneria dell’Informazione, University of Parma, Parma, Italy
This work describes a way to apply 3D Finite Element Analysis (FEA) to the thermal design of power electronic modules using simplified geometry models of the system components. The method here presented can overcome the problem of solving equation systems with a very high number of Degrees Of Freedom (DOF) due to complex geometry of a power module.