Mads Herring Jensen | February 25, 2015

When inside a room — a conference room, concert hall, or even a car — everyone has an opinion of when the “acoustics” are good or bad. In room acoustics, we want to study this notion of sound quality in a quantitative way. In short, room acoustics is concerned with assessing the acoustics of enclosed spaces. The Acoustics Module of COMSOL Multiphysics has several tools to simulate the acoustics of rooms and other confined spaces. I will present those here.

Read more ⇢

Article Categories

Bridget Cunningham | February 24, 2015

Continuous stirred tank reactors (CSTRs), or ideal stirred tank reactors, are frequently used in the chemical and biochemical industries. This reactor type operates at steady state and because of its good mixing properties, it is assumed that the composition throughout the reactor is uniform. Using a new model in the Reaction Engineering interface, we can visualize the dynamics within an ideal system of tank reactors.

Read more ⇢
Henrik Sönnerlind | February 23, 2015

We often get requests of the type “I would like to just enter my measured stress-strain curve directly into COMSOL Multiphysics”. In this new blog series, we will take a detailed look at how you can process and interpret material data from tests. We will also explain why it is not a good idea to just enter a simple stress-strain curve as input.

Read more ⇢

Article Categories

Pär Persson Mattsson | February 20, 2015

We have previously written about HPC with the COMSOL Multiphysics® software, clusters, and hybrid computing. But not all of us have a cluster available in the office (or the hardware to build a Beowulf cluster). So what possibilities do we have if we really need that extra compute power that a cluster can give us? One solution is to utilize cloud computing, a service that provides compute power on a temporary basis, to give our computations and productivity a boost.

Read more ⇢

Article Categories

Walter Frei | February 19, 2015

A thermostat is a device that senses the temperature of a system and uses this information to control the system’s heaters, or coolers, to keep the temperature close to a desired setpoint. While there are many different types of thermostats, we will focus today on one that turns a heater either on or off based upon two setpoints. This is known as an on-off or a bang-bang controller, and it can be implemented with the Events interface in COMSOL Multiphysics.

Read more ⇢
Bridget Cunningham | February 18, 2015

Space frames have been used as the foundation for the construction of many modern buildings, from the Louvre in France to Globen in Sweden. When designing space frames, we need to asses the risk of instability.

Read more ⇢

Article Categories

Walter Frei | February 16, 2015

One of the more common questions we are asked is about the modeling of periodic, or pulsed, heat loads. That is, a heat load that turns on and off repeatedly at known times. Modeling such a situation accurately and efficiently in COMSOL Multiphysics is quite easy to do with the Events interface. The techniques we will introduce are applicable to many classes of time-dependent simulations in which you have changes in loads that occur at known times.

Read more ⇢

Article Categories

Niklas Rom | February 13, 2015

Many exciting features for chemical engineering modeling were introduced in COMSOL Multiphysics version 5.0. In this blog post, I will discuss the most important updates. There are some new modeling interfaces, such as the Chemistry interface, and some that have been revamped and improved, like the Reaction Engineering interface. To begin with, I will recap the modeling interfaces for reaction engineering and mass transport.

Read more ⇢
Alexandra Foley | February 12, 2015

In the paper “Degeneracy Breaking, Modal Symmetry and MEMS Biosensors”, which was presented at the COMSOL Conference 2013 in Rotterdam, researchers experiment with using material and geometric symmetry breaking to design a MEMS biosensor.

Read more ⇢

Article Categories

Bridget Cunningham | February 11, 2015

The impact of light in various technologies has been evident in the past several years. Recognizing its significance in shaping the future, the UN General Assembly designated the year 2015 as the International Year of Light and Light-Based Technologies. We introduce you to a few interesting technologies in which light plays a crucial role.

Read more ⇢

Article Categories

Annette Meiners | February 10, 2015

Plasmas can exhibit a large variety of properties. There are plasmas with high and low ionization degrees, as well as those with high and low pressures and hot and cold temperatures. Different equations and modeling approaches are necessary for each kind of plasma. This blog post gives an overview of the different plasma types and shows when to use which of the interfaces available in the Plasma Module.

Read more ⇢

Article Categories

1 2 3 4 5 6 7 8 9 10 82