Technical Papers and Presentations

Here you will find presentations given at COMSOL Conferences around the globe. The presentations explore the innovative research and products designed by your peers using COMSOL Multiphysics. Research topics span a wide array of industries and application areas, including the electrical, mechanical, fluid, and chemical disciplines. Use the Quick Search to find presentations pertaining to your application area.

State of Charge (SOC) Governed Fast Charging Method for Lithium Based Batteries

F. Naznin[1]
[1]TVS Motor Company Ltd., Hosur, Tamil Nadu, India

The proposed State of Charge (SOC) governed fast charging method for secondary lithium based batteries charges a battery many times faster than the normal Constant Current-Constant Voltage (CC-CV) charging and reduces the side-effects generally accompanied by various fast charging methods. The proposed charging algorithm takes into account the varying internal impedance of the battery at ...

Screening Effects in Probing the Electric Double Layer by Scanning Electrochemical Potential Microscopy

R.F. Hamou[1], P.U. Biedermann[1], A. Erbe[1], and M. Rohwerder[1]
[1]Max-Planck-Institut für Eisenforschung GmbH, Düsseldorf, Germany

A computational method is developed to study probing the electric double layer by Scanning Electrochemical Potential Microscopy. The model is based on a modified Poisson- Boltzmann equation, which takes into account steric effects. We investigated the effect of metallic apex protrusion and the Open Circuit Potential (OCP) of the tip on the probed potential. A clear electrostatic screening effect ...

Simulation of Production Processes using the Multiphysics Approach: The Electrochemical Machining Process

R. van Tijum
Advanced Technology Center, Philips Consumer Lifestyle, Drachten, The Netherlands

Redmer van Tijum studied Applied Physics at the University of Groningen. In 2006, he received his PhD title on ‘Interface and surface roughness of polymer metal laminates’ in the field of Material Science at the University of Groningen. After that he became research and development engineer at Philips, where he focussed his attention on the improvement of production processes mainly ...

Simulation of Cyclic Voltammetry of Ferrocyanide/Ferricyanide Redox Reaction in the EQCM Sensor

H. Kwon, and E. Akyiano
Dept. of Engineering and Computer Science
Andrews University
Berrien Springs, MI

In this paper, the cyclic voltammetry behavior of Ferrocyanide/Ferricyanide, which is commonly used for electrochemical DNA detection experiment, was studied in the commercial EQCM-D setup (Q-sense) using the COMSOL Multiphysics. The model was established in a 3D geometry of QCM liquid cell. The simulation shows depletion of concentration of ferrocyanice following applied electrode potential. ...

Modeling Galvanic Corrosion

E. Gutierrez-Miravete[1], M. Turner[2]
[1]Rensselaer at Hartford, Hartford, CT, USA
[2]General Dynamics-Electric Boat, Groton, CT, USA

Galvanic corrosion is encountered in marine applications because one often has dissimilar metal joints and seawater acts as an electrolyte. One metal acts predominantly as anode and undergoes material dissolution while the other acts predominantly as cathode and is the site where a cathodic reaction takes place. Assuming a stagnant electrolyte, the equation governing the distribution of ...

Modeling the Vanadium Oxygen Fuel Cell

F.T. Wandschneider[1], M. Küttinger[1], P. Fischer[1], K. Pinkwart[1], J. Tübke[1], H. Nirschl[2]
[1]Fraunhofer-Institute for Chemical Technology, Pfinztal, Germany
[2]Karlsruhe Institute for Technology, Karlsruhe, Germany

A two-dimensional stationary model of a vanadium oxygen fuel cell is developed in COMSOL Multiphysics®. This energy storage device combines a vanadium flow battery anode and an oxygen fuel cell cathode. The oxygen reduction reaction generates additional water, leading to a degradation of the catalyst performance over time. A logistic function is introduced to the Butler-Volmer equation in order ...

Current Distribution on PEM Fuel Cells with Different Flow Channel Patterns

A. Paulino[1], E. Cunha[1], E. Robalinho[2], R. Passos[3], E. Santiago[1]
[1]Instituto de Pesquisas Energéticas e Nucleares, São Paulo, SP, Brazil
[2]Universidade Nove de Julho, São Paulo, SP, Brazil
[3]Universidade Federal do Amazonas, Manaus, AM, Brazil

In this paper, PEM fuel cells with serpentine and interdigitated flow channel patterns were studied. The main objective was to analyze the influence of the flow channel design in the current distribution over the cell. A 3D isothermal model comprising the entire 5 cm² cell was developed for this study. Polarization curves show that both cells have very similar performances. However, current ...

Electrochemical Modeling of Copper Electrorefining in Lab Scale and Pilot Plant Scale

D. Sujish[1], Jinimol Joy[1], B. Muralidharan[1], G. Padmakumar [1], K.K. Rajan[1]
[1]Fast Reactor Technology Group, Indira Gandhi Centre for Atomic Research, Kalpakkam, India

Pyrochemical reprocessing is a non-aqueous method for reprocessing spent metallic fuels. Electrorefining is an important step in pyrochemical reprocessing. Ambient temperature electrorefiner (ATER) is a facility to demonstrate the various mechanisms and associated interlocks. Here the electrolysis of copper in acidified copper sulphate electrolyte will be carried out to demonstrate the ...

Simulation of Current Density for Electroplating on Silicon Using a Hull Cell

F. Lima[1], U. Mescheder[1], H. Reinecke[3]
[1]Hochschule Furtwangen University, Furtwangen, Baden-Wuerttemberg, Germany
[3]Institut für Mikrosystemtechnik, Freiburg im Breisgau, Baden-Wuerttemberg, Germany

Electrodeposition has a major advantage over other methods of thin film deposition. It allows deposition at atmospheric pressure and room temperature, requiring inexpensive equipment. However, there are several parameters which can influence an electroplated metal layer quality. The current density distribution is taken into consideration. The Hull cell is an electrodeposition tank with a ...

The Effect of Electrolyte Flow Slots in Tooling Electrodes on Workpiece Surface Finish in Electrochemical Machining

B. Bingham[1]
[1]Oregon State University, Corvallis, OR, USA

Electrochemical machining (ECM) uses electrolysis to precisely remove material at high rates. ECM has many advantages over conventional machining: no tool wear, no induced mechanical or thermal stresses, high removal rates virtually independent of material hardness or strength, and excellent surface finishes. However, challenges can arise during the design of the tooling electrode when ...

Quick Search

1 - 10 of 194 First | < Previous | Next > | Last