T. Kaya, B. Shiari, K. Petsch, and D. Yates
Central Michigan University, School of Engineering and Technology, Mount Pleasant, MI
University of Michigan, Dept. of Electrical Engineering and Computer Science, Ann Arbor, MI
In this work, a MEMS low-g accelerometer with three sensitive directions is designed for health monitoring applications. The accelerometer may have different sensitivity in different axes. The proof-mass of the device is suspended by four serpentine springs, and the comb drive structure is used to form the differential capacitor to measure the displacement of the proof-mass. The structure has an ...
J. Crompton, S. Yushanov, L. Gritter, and K. Koppenhoefer
AltaSim Technologies, LLC.
Thermoelectric phenomena provide the direct conversion of heat into electricity or electricity into heat, the phenomena is described by three related mechanisms: the Seebeck, Peltier and Thomson effects. Thermoelectric devices have found many applications ranging from temperature measurement, solid state heating or cooling and direct energy conversion from waste heat. In this paper, analysis ...
H. Kwon, and E. Akyiano
Dept. of Engineering and Computer Science
Berrien Springs, MI
In this paper, the cyclic voltammetry behavior of Ferrocyanide/Ferricyanide, which is commonly used for electrochemical DNA detection experiment, was studied in the commercial EQCM-D setup (Q-sense) using the COMSOL Multiphysics. The model was established in a 3D geometry of QCM liquid cell. The simulation shows depletion of concentration of ferrocyanice following applied electrode potential. ...
N. Elabbasi, J. Bergstrom, and S. Brown
Veryst Engineering, LLC.
Peristaltic pumping is an inherently nonlinear multiphysics problem where the deformation of the tube and the pumped fluid are strongly coupled. We used COMSOL Multiphysics to investigate the performance of a 180 degree rotary peristaltic pump with two metallic rollers, and an elastomeric tube pumping a viscous Newtonian fluid. The model captures the peristaltic flow, the flow fluctuations ...
D. Groulx, and R. Murray
COMSOL Multiphysics can be used to model a latent heat energy storage system. A 2D numerical study was performed to simulate melting of a PCM including both conduction and convective heat transfer. The heat transfer in fluids and laminar flow physics interfaces were used. To model natural convection, proper volume force was applied to the PCM. The viscosity was input as a piecewise, continuous ...
T. Eppes, I. Milanovic, and G. Quarshie
University of Hartford
West Hartford, CT
Power transistors require heat sinks to dissipate thermal energy and keep junction temperatures below the recommended limit. The reliability and longevity of any semiconductor device is inversely proportional to the junction temperature. Hence, a significant increase in reliability and component life can be achieved by a small reduction in operating temperature. A range of heat sink designs ...
M. Haghighi-Yazdi, and P. Lee-Sullivan
University of Waterloo
In this study, a capability has been developed for modeling the linear viscoelastic behaviour of a glassy polymer using COMSOL Multiphysics®. The two rheological models by Maxwell and Kelvin-Voigt were used for modeling stress relaxation and creep loading behavior, respectively, of a typical gas pipe under two modes of plane stress and plane strain. An advantage of the developed model is its ...
J. Strong, and C. Washburn
Sandia National Laboratories
The newly emerging field of carbon-based MEMS (C-MEMS) attempts to utilize the diverse properties of carbon to push the performance of MEMS devices beyond what is currently achievable. Our design employs a carbon-carbon composite using nano-materials to build a new class of MEMS accelerometer that is hyper-sensitive over a dynamic range from micro-G to hundreds of G’s – far surpassing the ...
Optimization of Design Parameters of a Novel MEMS Strain Sensor used for Structural Health Monitoring of Highway Bridges
H. Saboonchi, and D. Ozevin
Civil Engineering Department
University of Illinois at Chicago
The novel Micro Electro Mechanical System (MEMS) based Piezoresistive stain sensor is presented in this paper. The main goal of this sensor is to monitor the localized strain in the highway bridges especially near the crack tips. Monitoring the crack growth on the bridges can lead to early detection and prevention of bridge failures. The COMSOL Multiphysics software was used to optimize the ...
Modeling and Simulation of Artificial Core-Shell Based Nanodielectrics for Electrostatic Capacitors Applications
D. Musuwathi Ekanath, N. Badi, and A. Bensaoula
Center for Advanced Materials, University of Houston, Houston, TX
Dept. of Physics, University of Houston, Houston, TX
The need for high storage capacitors led to the development of polymer based capacitors. Polymers have high processability, mechanical flexibility, electrical breakdown strength and compatibility with printed circuit board (PCB) technologies; but usually have very low permittivity (K). In COMSOL Multiphysics software, the AC/DC module is selected and the In-plane electric currents are applied ...